Tajas post a comment:

Use the Constrain command or Assemble command to place an Insert constraint. An Insert constraint places a planar and axial mate as a single constraint between selected cylindrical faces or edges. For autodesk inventor 2016 assembly constraints free, use an Insert constraint to position a bolt in a hole.

The bolt is free to rotate, but is constrained plane to plane and axis to axis. To begin, place the components to constrain in an assembly file. Clear the check box to remove limits. Values are retained in an inactive state.

In the dialog box, under Type, click Insert constraint. Select the first arc or circle edge. If necessary, click First Selection to enable the selection.

Use Select Other to cycle through geometry. Select the second arc or circle edge to constrain to the first selection. If necessary, click Second Selection to enable the selection. Enter an autodesk inventor 2016 assembly constraints free value, if applicable. Click Opposed or Aligned to reverse the direction of the constraint.

Click the More button to change the name the constraint or set limits. In the Name box, enter a constraint name, or leave blank and a default name is automatically created. Check Maximum and enter a value to specify the maximum limit position. Check Minimum and enter a value to autodesk inventor 2016 assembly constraints free the minimum limit position. Check Use Offset As Resting Position and enter consttaints required value in the Offset value box to specify the resting position.

If Show Preview is selected, observe the effects of the applied constraint. If either component is adaptive, constraints are not previewed. Do one of the following: Click OK to create the constraint and close the dialog box. Click Apply and continue to place constraints. Show Me constrainfs to insert a constraint. Select an arc or circle edge on the component that changes position. Select an arc or circle autodesk inventor 2016 assembly constraints free on the component that remains in position.

Change the solution from Insert-Opposed to Insert-Aligned to reverse the direction of the constraint. Do one of the following: Click Apply and continue to define constraints. Click OK to create the constraint and exit the Assemble command. Click Dree to delete the selections and continue to define constraints. Note: If other components obscure selection, do one of the following: Temporarily turn off visibility before you place a constraint.

Click in the browser to select a component, right-click, autodesk inventor 2016 assembly constraints free then select Visibility. To restrict selectable geometry to a specific part, select Pick Part First in the dialog box, and then click the component constraintz want to constrain.

Clear Pick Part First to restore normal selection mode. Parent topic: Assembly relationships overview.

Vogrel post a comment:

When you constrain or join assembly components to one another, you control their position. To move or rotate a component, either temporarily or permanently, use one of the following methods: Free move You can move a component to get a better view of its features or to analyze relationships. A free move is a temporary "get out of the way" move. You might want to move .

Shakarn post a comment:

Assembly constraints and assembly joints both create relationships that determine component placement and allowable movement. The Constrain and Assemble commands are legacy methods of positioning components and gradually eliminating degrees of freedom (DOF) using constraints. The Joint command reduces the complexity of component relationships. Use . Sep 24,  · Welcome to Autodesk’s Inventor Forums. Share your knowledge, ask questions, and explore popular Inventor topics. It is very clumsy, because I have to go to each of the two parts, turn on visibility of the axes, go to the assembly, add the constraint, then go back to the two parts and turn off the visibility. The center axis and pin. Assembly constraints establish the orientation of the components in the assembly and simulate mechanical relationships between components. For example, you can: Mate two planes. Specify that cylindrical features on two parts remain concentric. Constrain a spherical face on one component to remain tangent to a planar face on another replace.meted Reading Time: 5 mins.%

Dikazahn post a comment:

allowed to assemble the components using the smart assembly constraints and joints. enhancements and information related to Autodesk Inventor Use the Constrain command or Assemble command to place an Insert constraint. An Insert constraint places a planar and axial mate as a single.

Mezikinos post a comment:

Message 3 of 3. Grip Snap move options.